Christen Eagle II 90 ARFAssembly Manual
10 Hangar 9 Christen Eagle II 90 ARF 7. Remove the T-pins from the hinges and make sure the gap between the elevators and stabilizer are as small as
11Hangar 9 Christen Eagle II 90 ARF 13. Once the stabilizer has been aligned, use a felt-tipped pen to transfer the outline of the fuselage onto the
12 Hangar 9 Christen Eagle II 90 ARF 19. Mix 1/3 ounce (10mL) of 30-minute epoxy. Apply the epoxy to the exposed wood at the bottom of the fin as wel
13Hangar 9 Christen Eagle II 90 ARF 4. Use a pin vise and 5/64-inch (2mm) drill bit to drill the holes for the mounting screws. Use a #1 Phillips scr
14 Hangar 9 Christen Eagle II 90 ARF 3. Mount the receiver in the fuselage using a hook and loop strap and 1/4 inch (6mm) of foam rubber (not include
15Hangar 9 Christen Eagle II 90 ARF 8. Mount the switch harness in the fuselage using the hardware provided with the switch and a #1 Phillips screwdr
16 Hangar 9 Christen Eagle II 90 ARF 5. Prepare the aileron servo by installing the grommets and brass eyelets. Use a #1 Phillips screwdriver and th
17Hangar 9 Christen Eagle II 90 ARF 11. Thread a clevis on each end of the 3mm x 70mm threaded rod. Set the distance between the pins of the clevise
18 Hangar 9 Christen Eagle II 90 ARF 4. Place the upper center wing rib in position on the cabane struts. Start the M3 x 10 socket head screws that s
19Hangar 9 Christen Eagle II 90 ARF 5. Remove the template from the fuselage. Use a 7/32-inch (5.5mm) drill bit to enlarge the holes in the firewall.
2 Hangar 9 Christen Eagle II 90 ARF WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.
20 Hangar 9 Christen Eagle II 90 ARF4-Stroke Engine InstallationRequired PartsFuselage assembly Engine mount (right and left)M4 washer (12) M4 blind
21Hangar 9 Christen Eagle II 90 ARF 7. Position the engine on the engine mount rails so the face of the drive washer is 511/16 inches (145mm) from th
22 Hangar 9 Christen Eagle II 90 ARF 3. Attach the clunk to the straight line (carburetor tube) using a piece of fuel tubing. Cut the fuel tubing so
23Hangar 9 Christen Eagle II 90 ARF 9. Position the plywood fuel tank retainer so the tabs are inserted into the slots on the tank former. The retain
24 Hangar 9 Christen Eagle II 90 ARF 5. Attach the pushrod connector to the servo arm so it is located 5/8 inch (16mm) from the center of the arm. Ma
25Hangar 9 Christen Eagle II 90 ARF 3. With the spinner backplate tight against the engine drive washer, position the cowl so there is a 1/16-inch (1
26 Hangar 9 Christen Eagle II 90 ARF 9. Use silicone adhesive to glue the baffle into the cowling to direct air over the head of the engine. Allow th
27Hangar 9 Christen Eagle II 90 ARF 15. Mount the spinner and propeller. Use open-end or box wrenches to tighten the propeller nut. Check the fit of
28 Hangar 9 Christen Eagle II 90 ARF 6. Slide the wing into position on the fuselage. Slide the wing tight against the fuselage. Use an M3 x 12 socke
29Hangar 9 Christen Eagle II 90 ARFREMOVING THE WING PANELS 12. Locate the wing transport frames and rubber bands. Slide the frames between the top
3Hangar 9 Christen Eagle II 90 ARFQUANTITY DESCRIPTION AND USAGE1 ...Fuselage with hatch, pushrods and landing gear attach bolts1 ...
30 Hangar 9 Christen Eagle II 90 ARF 3. When balancing your model, make sure it is assembled and ready for flight. Support the plane inverted at the
31Hangar 9 Christen Eagle II 90 ARFPreightCheck Your RadioBefore going to the field, ensure your batteries are fully charged per your radio’s instruc
32 Hangar 9 Christen Eagle II 90 ARFLIMITATION OF LIABILITYHORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOS
33Hangar 9 Christen Eagle II 90 ARFUNITED KINGDOMHorizon Hobby LimitedUnits 1-4 Ployters RdStaple TyeHarlow, EssexCM18 7NSUnited Kingdomsales@horizonh
34 Hangar 9 Christen Eagle II 90 ARF6. With the exception of events flown under official AMA Competition Regulations, excluding takeoff and landing,
35Hangar 9 Christen Eagle II 90 ARFBuilding and Flying Notes
32527TMPrinted 10/2011© 2011 Horizon Hobby, Inc.horizonhobby.com Hangar9.comHangar 9, Evolution, JR, DSM2, DSMX, PowerPro, EC3, UltraCote and the Hori
4 Hangar 9 Christen Eagle II 90 ARF Safety Precautions and WarningsRead and follow all instructions and safety precautions before use. Improper use ca
5Hangar 9 Christen Eagle II 90 ARFSafe Operating Recommendations• Inspectyourmodelbeforeeveryflighttoensureitisairworthy.• Beawareofa
6 Hangar 9 Christen Eagle II 90 ARFField Equipment RequiredFuel (15% recommended)Saito Glow Plug SAIP400SLong Reach Glow Plug Wrench HAN2510Metered
7Hangar 9 Christen Eagle II 90 ARFLanding Gear InstallationRequired PartsFuselage Landing gearM3 washer (2) Wheel pant (right and left)Landing gear
8 Hangar 9 Christen Eagle II 90 ARF 7. Fit the 20mm x 15mm plywood plate to the wheel pant so the blind nut aligns with the mounting hole in the whe
9Hangar 9 Christen Eagle II 90 ARFTail InstallationRequired PartsFuselage Stabilizer with elevatorsRudder with fin Black-covered balsa blockBottom w
Kommentare zu diesen Handbüchern